Omron PLC Training Course

Programming Omron PLCS by CX-Programmer

In this course, you can learn about more useful Omron PLC in CX-Programmer.

What you’ll learn

  • Working with Omron PLC in CX-Programmer Program.

Course Content

  • Omron Basic Instruction –> 22 lectures • 3hr 41min.
  • Problems –> 2 lectures • 36min.
  • Function Block –> 3 lectures • 42min.
  • Security –> 2 lectures • 16min.
  • Working with CX-Programmer environment –> 1 lecture • 16min.

Omron PLC Training Course

Requirements

  • Have Some Knowledge about PLC.

In this course, you can learn about more useful Omron PLC in CX-Programmer.

With CX-Programmer that included in CX-One Package you can Program Below PLC Series:

CP1E, CP2E, CP1L, CP1H, CJ2M, CS1

You can download the CX-Programmer Trial Version from Omron Website.

Also after seeing the video you can send any question to me I can answer your questions.

Also, this course can be edited at your request.

Course Details:

– DIFU/DIFD

* DIFU(013) turns the designated bit ON for one cycle when the execution condition goes from OFF to ON (rising edge).

* DIFD(014) turns the designated bit ON for one cycle when the execution condition goes from ON to OFF (falling edge).

 

– TIM/TIMX

* TIM or TIMX(550) operates a decrementing timer with units of 0.1-s.

 

– CNT/CNTX

* CNT/CNTX(546) operates a decrementing counter.

 

– KEEP/SET/RSET

* KEEP Operates like a latching relay.

* SET turns the operand bit ON when the execution condition is ON. After this, the specified contact will remain ON regardless of  ON/OFF of the input condition.

* RSET turns the operand bit OFF when the execution condition is ON. After this, the specified contact will remain OFF regardless of ON/OFF of the input condition.

 

– MOV

*Transfers a word of data to the specified word.

 

– CMP

* Input comparison instructions compare two values (constants and/or the contents of specified words) and create an ON execution condition when the comparison condition is true. Input comparison instructions are available to compare signed or unsigned data of one-word or double-length data.

 

– CMP/CMPL

* CMP : Compares two unsigned binary values (constants and/or the contents of specified words) and outputs the result to the Arithmetic Flags in the Auxiliary Area.

* CMPL : Compares two double unsigned binary values (constants and/or the contents of specified words) and outputs the result to the Arithmetic Flags in the Auxiliary Area.

 

– INC/DEC

* Increments the 4-digit hexadecimal content of the specified word by 1.

* Decrements the 4-digit hexadecimal content of the specified word by 1.

 

– ASL/ASR

* ASL : Shifts the contents of Wd one bit to the left.

* ASR : Shifts the contents of Wd one bit to the right.

 

– SLD/SRD

* SLD : Shifts data by one digit (4 bits) to the left.

* SRD : Shifts data by one digit (4 bits) to the right.

 

– BSET

* Copies the same word to a range of consecutive words.

 

– MOVB

* Transfers the specified bit.

 

– MOVD

* Transfers the specified digit or digits. (Each digit is made up of 4 bits.)

 

– NASL/NASR

* NASL : Shifts the specified 16 bits of word data to the left by the specified number of bits.

* NASR : Shifts the specified 16 bits of word data to the right by the specified number of bits.

 

– MCMP

* Compares 16 consecutive words with another 16 consecutive words and turns ON the correspond­ing bit in the result word where the contents of the words are not equal.

 

– MTIM

* Compares 16 consecutive words with another 16 consecutive words and turns ON the correspond­ing bit in the result word where the contents of the words are not equal.

 

– TCMP

*Compares the source data to the contents of 16 consecutive words and turns ON the corresponding bit in the result word when the contents of the words are equal.

 

– TIML

* TIML(542)/TIMLX(553) operates a decrementing timer with units of 0.1s.

 

– TTIM

* TTIM(087)/TTIMX(555) operates an incrementing timer with units of 0.1-s.

 

– SETA/RSTA

* SETA(530) turns ON the specified number of consecutive bits.

* RSTA(531) turns OFF the specified number of consecutive bits.

 

– OUTB

* OUTB(534) outputs the status of the instruction’s execution condition to the specified bit.

 

– XFER

* Transfers the specified number of consecutive words.

 

– XCHG

* Exchanges the contents of the two specified Words

Get Tutorial